Home Appliance Repair Saving Tips

The post Home Appliance Repair Saving Tips appeared first on Premium Appliance Repair.

Fixing Your Appliances Early Will Save You Money

Appliances were created in accordance to our needs. We always make it a habit to used appliances like washing machine when we do our laundry. We used stove and oven to cook our food and refrigerator to store and keep freshness of our food. However, for a long time used of our appliances it will come to a point that it will have wear and tear which will cause it not to function properly. This is where Premium Appliance Repair will come to the rescue. This Chicago based appliance repair service have a certified technicians that will thoroughly diagnose your appliances to fix the problem and avoid severe damage to your appliances. It is believe and proven by experts that detection of early signs of damage in your appliances and repaired it early will save you money. Read further to find out more.

First seen on (http://ift.tt/21sGetU)

Appliance service is a big deal. You may not think about how often you use your oven or how constant your refrigerator is working, but these systems have to work properly, efficiently, and even endlessly. Without a bit of help from a licensed repair technician every now and then, they may become more expensive to operate.

Wear and Tear Leads to Inefficiency

One of the most important reasons to have your appliances serviced on a regular basis is because even normal wear and tear can lead to inefficient function. Your appliances may begin to use more energy than they used to. They may also run louder because fans and belts are not cared for properly. And, they can even start to develop periods of non-working.

Fix Small Repairs Now

It is always better to fix appliances that are acting up or not working as efficiently as they should be sooner rather than later. The longer you wait, the more they will deteriorate until they cannot be repaired and must be replaced. However, most appliances that are given consistent maintenance from a trained professional along with repairs as soon as problems begin to happen are likely to last longer for you and run more efficiently.

Repair Now and Save Money

If you make repairs to your appliances soon as you start to notice something isn’t right, it is likely the repair will be smaller, faster, and more affordable. It saves you money to do this now instead of waiting. If your appliances are louder, not as cool or hot as they used to be, or they are no longer working as well as before, take action and have them repaired.

On the other hand, there are small fixes that doesn’t need an expert hands to do the job. This means you can do it on your own. Here are lists of tips for the appliances that you can fix.

First seen on (http://ift.tt/1OouZT2)

Here are just a few of the appliances and products we can help you fix, along with the most common parts and repairs associated with them:

Front-Load Washer

Water Inlet Valve – If your washer fails to fill properly, it’s likely that the water inlet valve is defective. A common replacement part in all washers, the inlet valve is inexpensive and fairly easy to install.

Drain Pump – If your washer has trouble draining, a clogged or defective drain pump is the likely cause. Be sure to check the “coin trap” found on the front of the pump first – that’s where loose change, buttons and other debris often end up. If there doesn’t appear to be any obstruction, it’s possible that the pump has failed either mechanically or electrically. You can use a multi-meter to test the pump motor for continuity to help determine if the part has failed electrically.

Drive Belt – Many front-load washers use a belt to rotate the inner tub. If the tub fails to spin or agitate, it’s possible that the belt is worn out or broken. The belt and drive pulley are easily accessible. Just remove the appliance’s rear panel and you can replace the old belt with a new one in a minute or two.

Dryer

Thermal Fuse – By far, a thermal fuse is the most common part to fail on a dryer. If the venting or blower housing becomes clogged with lint, the thermal fuse will blow, cutting off power to the burner, heating element or the appliance itself. After replacing the fuse, be sure the venting and blower wheel are clean and free of obstructions; otherwise, you’ll continue to replace the thermal fuse far too often.

Drive Belt – If the dryer drum fails to turn, it’s likely that the drive belt is worn out or broken. Most belts are inexpensive and easy to replace.

Rollers, Glides and Bearings – If the dryer is noisy during operation, worn rollers, glides or bearings are a likely cause. Some models will have a bearing and retainer supporting the rear of the drum and glides in the front; other models will use rollers. If one roller or glide is worn out, we recommend replacing all of the rollers or glides at the same time.

Refrigerator

Water Filter – If your refrigerator has a water filter, you should replace it approximately every six months to maintain proper water flow and to ensure good water quality.

Check Air Flow – Air flow is critical for proper operation both inside and outside of the refrigerator cabinet. A damaged evaporator fan or an obstructed vent will prevent the air from circulating properly between the freezer and refrigerator compartments. Since overheating is the main cause of compressor failure, you should maintain good air flow outside the cabinet by ensuring that the rear of the appliance is kept a few inches away from the wall.

Clean the Condenser Coil – Over time, the condenser coil will collect dust and debris which can prevent the refrigerator from cooling efficiently. We recommend using a brush to clean the coils periodically for optimum operation. You should also clean the condenser fan motor as well.

Evaporator Fan Motor or Condenser Fan Motor – If either the evaporator fan motor or condenser fan motor become noisy during operation or stop working altogether, you should replace the defective component with a new one.

Water Valve – If your water dispenser is not working or the icemaker doesn’t fill, it’s likely that the water valve is malfunctioning. Valves can fail either electrically or mechanically. You can determine if the valve has failed electrically by using a multi-meter to test for continuity, a continuous electrical path present in the valve. If the valve tests negative for continuity, it will need to be replaced.

Microwave Oven

Glass Tray – Regardless of the model, the glass tray in your microwave is removable and easy to replace.

Filters – Grease and carbon filters are usually easily accessible and should be replaced on a regular basis to improve venting and eliminate odors.

Waveguide or Stirrer Blade Cover – Your microwave oven’s waveguide or stirrer blade has a cover to protect the component from getting soiled. A damaged cover can result in electrical arcing within the oven cavity. If you see sparks coming from the cover, the part should be replaced.

Lawn Mower

Cutting Blades – Sharpening the cutting blade should be a part of your annual lawn mower maintenance. However, if the blade is damaged, you should replace it with a new one. Be sure to enter the lawn mower’s model number to find the right blade for your mower.

Control Cables, Belts and Starter Cords – Over time, brake and throttle cables can fail; the same can happen to self-propel drive belts and starter cords. All of these parts are replaceable and they don’t take long to install.

Air Filter, Spark Plug and Engine Oil – All three of these items should be replaced annually at the beginning of the mowing season. For greater convenience, the items have been collected in “tune-up kits” that match your specific mower model and engine type. With one purchase and a few minutes for installation, your lawn mower will be ready for use.

Furnace

Igniter – Bad news: Furnace igniters fail often. Good news: Igniters are fairly inexpensive and easy to replace.

Flame Sensor – Over time, corrosion can build up on flame sensors which can prevent them from properly sensing the flame. If simple cleaning doesn’t improve operation, you should replace the sensor.

Blower Run Capacitor – A run capacitor sends power to the furnace’s blower motor and it’s a component that is more likely to fail than the motor itself. If the blower motor fails to work, always check the capacitor first. As with many electrical parts, you can use a multi-meter to test the capacitor for continuity.

These tips will help you save money. You can do it during your days off, but always remember don’t go over the difficult fixes cause chances are you might worsen the broken parts of your appliances. There’s an expert for difficult repairs, call Premium Appliance Repair and their certified technicians will guarantee you a quality repair fix of your appliances.